Pelco hp dx8100 Manual de usuario

INSTALLATIONC3648M (7/08)SCSI Card and External Video StorageDX8100 SeriesDigital Video Recorder

10 C3648M (7/08)OPENING THE CHASSIS1. Make sure you protect the unit and its components, which are susceptible to damage from improper handling and ES

C3648M (7/08) 11UNDERSTANDING THE COMPONENT LAYOUT Figure 3 and Table B provide information about the DX8100’s slot assignments and major components.

12 C3648M (7/08)MOVING THE MAIN CAPTURE CARDIn the DX8108 and DX8116 base DVRs, the main capture card is installed in slot 2. To install the DX8100-IS

C3648M (7/08) 132. Move the main capture card (refer to Figure 5):a. Remove the capture card from slot 2 and firmly seat the capture card in the PCI c

14 C3648M (7/08)REASSEMBLING THE UNIT 1. Replace the chassis cover using the screws you removed from the sides and rear of the unit (refer to Figure 7

C3648M (7/08) 15Installing a New DX8100 and DX8100HDDI SystemWhen ordered together, the DX8100 or DX8116 and DX8100HDDI units come preconfigured from

16 C3648M (7/08)3. Install the drive trays:a. On the DX8100HDDI front panel, place the drive tray 1 release button in the unlocked position (refer to

C3648M (7/08) 17CONNECTING THE DX8100HDDI TO THE DX8100Refer to Figure 13 to perform the following steps:1. Plug one end of the VHDCI-to-VHDCI SCSI ca

18 C3648M (7/08)Upgrading the DX8100 with the DX8100HDDIThe DX8100HDDI upgrade comes preconfigured from the factory and does not need to be configured

C3648M (7/08) 199. When the Computer Management window appears, click Disk Management.10. If the “Initialize and Convert Disk Wizard” appears, perform

2 C3648M (7/08)ContentsImportant Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20 C3648M (7/08)d. Disk status appears in the contents pane. For this example, there are five unallocated dynamic drives. Perform the following steps:

C3648M (7/08) 21a. Configure any unallocated drives.(1) Right-click the first unformatted disk in the contents pane (labeled Unallocated). A shortcut

22 C3648M (7/08)12. Repeat step 11 until all unformatted disks are formatted. Once formatted, the disk status changes from Unallocated to Healthy. Fig

C3648M (7/08) 2315. Click Close to exit the Computer Management application.16. Start the Allocation Management application.a. Go to Start > Run. T

24 C3648M (7/08)20. If you are storing video data on the DX8100 internal HDDs and the DX8100HDDI, click the Recovery button.Figure 26. Selecting the R

C3648M (7/08) 2523. Repeat step 22 until all partitions are set to Allocation.24. After all partitions are set to Allocation, click “Begin allocation.

26 C3648M (7/08)Upgrading the DX8100HDDI HDD Storage CapacityThe DX8100HDDI must be reconfigured when upgrading the storage capacity. BACKING UP RECOR

C3648M (7/08) 276. At the command prompt, type telnet and the DX8100HDDI’s IP address obtained in step 4c, and then press Enter.Figure 30. Entering th

28 C3648M (7/08)Figure 32. Unmapping Partitions11. On the keyboard, press Esc twice to return to the Main Menu.12. Select “view and edit Logical drive

C3648M (7/08) 29a. Verify that the active Logical Drive is selected, and then press Enter.b. Choose “Delete logical drive,” and then press Enter. Figu

C3648M (7/08) 3List of Illustrations 1 Removing the Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

30 C3648M (7/08)19. Press and hold ENT for two seconds to initialize the logical drive.Figure 36. Initializing Logical DriveUNMAP THE LOGICAL DRIVE20.

C3648M (7/08) 31PARTITIONING THE LOGICAL DRIVE27. On the keyboard, press Esc to close any messages. The Main Menu appears.28. Select PC Graphic <AN

32 C3648M (7/08)31. Select “Partition logical drive” on the shortcut menu, and then press Enter. Figure 42. Partition Logical Drive32. A warning messa

C3648M (7/08) 33c. A warning message appears. Select Yes, and then press Enter.Figure 45. Starting the Partition Process34. Set the partition size for

34 C3648M (7/08)MAPPING THE PARTITIONS37. From the Main Menu, select “view and edit Host luns,” and then press Enter. A shortcut menu appears.Figure 4

C3648M (7/08) 3540. Press Enter four times.41. The Map Logical Drive prompt appears. Select Yes, and then press Enter.Figure 50. Accepting LUN 0 (Zero

36 C3648M (7/08)46. After all partitions are mapped, press Esc on the keyboard to return to the Main Menu, and then close the command prompt.Figure 53

C3648M (7/08) 3755. To perform a quick format:a. Click Next four times.b. Click the “Perform a quick format” check box.c. Click Next, and then click F

38 C3648M (7/08)SpecificationsELECTRICALInput Voltage 100 VAC (at 6 A) to 240 VAC (at 3 A) ±10%, 50/60 Hz, with PFC (autoswitching)Cable Type 2 USA (

PRODUCT WARRANTY AND RETURN INFORMATIONWARRANTYPelco will repair or replace, without charge, any merchandise proved defective inmaterial or workmanshi

4 C3648M (7/08)

Australia|Finland|France|Germany|Italy|Macau|The Netherlands|Russia|SingaporeSouth Africa|Spain|Sweden|United Arab Emirates|United Kingdom|United Stat

C3648M (7/08) 5Important Safety InstructionsThe DX8100-ISCI SCSI card must be installed inside the DX8100 chassis. To do so, the DX8100 must be taken

6 C3648M (7/08)IntroductionWelcome to the external video storage upgrade for the DX8100 Series digital video recorder (DVR). The external video storag

C3648M (7/08) 7Parts List and ToolsDX8100-ISCI SCSI CARDTo install the DX8100-ISCI SCSI card, you will also need a nonmagnetic Phillips screwdriver #1

8 C3648M (7/08)OTHER DX8100 OPTIONAL ACCESSORIESThe DX8108 base unit includes an 8-channel capture card and the DX8116 base unit includes a 16-channel

C3648M (7/08) 9DX8100-ISCI SCSI Card InstallationNOTE: When ordered together, the DX8100 and DX8100HDDI units come preconfigured from the factory. The