Pelco Switch C1528M-F Manual de usuario

® CM6800E-48X8Matrix Switcher/Controller INSTALLATION/OPERATION C1528M-F (6/05)

10 C1528M-F (6/05) Programming The CM6800E features easy programming through on-screen menus or the Windows ® -based CM6800-MGR software package. Al

100 C1528M-F (6/05)Matrix switcher This is also known as a cross-point switcher. The cross-points are actually electronic switches that select any vid

C1528M-F (6/05) 101RS-422 This is an Electronics Industry Association (EIA) interface standard. Pelco uses this standard for communication from a cont

102 C1528M-F (6/05)SpecificationsGENERALMemory Protection: Lithium battery, five years of data protection Keyboards: Eighteen: Sixteen KBD100/200A/300A

C1528M-F (6/05) 103Regulatory Notices48 x 8 SystemIn a 48 x 8 system, this equipment complies with part 15 of the FCC Rules. Operation is subject to t

104 C1528M-F (6/05)

PRODUCT WARRANTY AND RETURN INFORMATIONWARRANTYPelco will repair or replace, without charge, any merchandise proved defective in material orworkmanshi

®Worldwide Headquarters3500 Pelco WayClovis, California 93612 USAUSA & CanadaTel: 800/289-9100Fax: 800/289-9150InternationalTel: 1-559/292-1981Fax

C1528M-F (6/05) 11 Alarm Inputs Eight internal alarm inputs are provided on the rear panel of the matrix switcher/controller. These internal alarm in

12 C1528M-F (6/05) MODEL CM6800E-48X8 Matrix switcher/controller with 48 video inputs and 8 monitor outputs, NTSC-configured, 120/230 V, 50/60 Hz, aut

C1528M-F (6/05) 13 Installation Unpack and inspect all parts carefully. The following parts are supplied:1 CM6800E Switcher/Controller 4 10-32 x .750

14 C1528M-F (6/05) VIDEO SOURCES The CM6800E offers 48 full-function video inputs which support Coaxitron PTZ control and video loss detection. Forty

C1528M-F (6/05) 15 2. On video inputs 1 through 40, set the terminating switches according to your system requirements. Video inputs 41 through 48 ca

16 C1528M-F (6/05) CONTROL LINES You cannot connect a Coaxitron camera to the PTZ-A or PTZ-B ports. If your video sources are all controlled by Coaxi

C1528M-F (6/05) 17 MONITORS The CM6800E supports eight monitors. 1. Install monitors according to the instructions provided with them.2. Connect the

18 C1528M-F (6/05) ALARMS The CM6800E provides numerous alarm handling options. Refer to the Programming section for a detailed description.1. Conn

C1528M-F (6/05) 19 CONNECTING DEVICES THROUGH THE COMMUNICATION PORTS The CM6800E Matrix Switcher/Controller provides eight communication ports on th

20 C1528M-F (6/05) NOTE: Refer to the Programming section for instructions on changing Port settings.7 RJ-45 RS-485 or RS-232 RS-485 Pin-Outs:1 R

C1528M-F (6/05) 21 Figure 13. CM6800E Communication Port Connections and Options12345678168763231432120/230~50/60 HZ25 WATTS 123 45678CONTROL AT+

22 C1528M-F (6/05) KBD100, KBD200A, AND KBD300A SERIES KEYBOARDS You can connect up to eight KBD100/200A/300A Series keyboards to any of the followin

C1528M-F (6/05) 23 3. Set the keyboard DIP switches for the desired address for the local keyboard (refer to Figure 12 and Table D). Table D. Keyb

24 C1528M-F (6/05) KBD100, KBD200A, and KBD300A: Remote Keyboards Use COM 5, 6, 7, or 8 for remote keyboard connections. Each port can support up to

C1528M-F (6/05) 25 M DEVICES (KBD960, ALM2064, REL2064) M protocol devices (KBD960/KBR960 keyboards, ALM2064 Alarm Interface Units, and REL2064 Relay

26 C1528M-F (6/05) Connecting a Single KBD960/KBR960 Keyboard To connect a single KBD960/KBR960 Keyboard to the CM6800E: 1. Connect the keyboard to

C1528M-F (6/05) 27 Connecting a Single ALM2064 Alarm Interface UnitTo connect a single ALM2064 Alarm Interface Unit: 1. Connect the ALM2064 OUT port

28 C1528M-F (6/05)Connecting a Single REL2064 Relay Interface Unit To connect a single REL2064 Relay Interface Unit: 1. Connect the REL2064 OUT port t

C1528M-F (6/05) 29Multiple M Devices Multiple M devices (KBD960/KBR960, ALM2064, and REL2064) can be connected to COM 3 on the CM6800E, either as loca

C1528M-F (6/05) 3 Contents Important Safeguards and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

30 C1528M-F (6/05)Multiple M Devices: Remote ConnectionUse a remote connection when the distance from the CM6800E is greater than 6-feet (1.8 m).1. Co

C1528M-F (6/05) 31CONNECTING A PCThe CM6800E provides PC-based setup and programming software that facilitates complete switcher programming and config

32 C1528M-F (6/05)CONNECTING GENEX MULTIPLEXERSUse COM 4 to connect up to eight Genex Multiplexers to the CM6800E. 1. Connect the COM IN port of the m

C1528M-F (6/05) 33LOCAL AUXILIARIESThe CM6800E provides three local auxiliary (AUX) outputs on the rear panel for controlling VCRs, printers, and othe

34 C1528M-F (6/05)Connecting the Open Collector Output – F3 (TTL)F3 is a TTL open collector output. This output provides a path to ground to control t

C1528M-F (6/05) 35CONNECTING A 96 X 16 SYSTEM1. Install each CM6800E-48X8 unit and connect appropriate devices to each unit. Note that the CM6800E-48X

36 C1528M-F (6/05)System Start-upAfter completing the system installation, follow the procedure below to start proper system operation. Skip any “syst

C1528M-F (6/05) 37CONFIGURE THE SYSTEMThe CM6800E is shipped from the factory with default programming settings. If the defaults are acceptable, the C

38 C1528M-F (6/05)96 X 16 SYSTEM SETTINGSWhen you connect two CM6800E-48X8 units together in a 96 x 16 system, you must access the System programming

C1528M-F (6/05) 39MONITOR COLOR ADJUSTMENTOnce you have connected all devices and powered the system, use the CM6800E color bars as a reference tool f

4 C1528M-F (6/05) Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

40 C1528M-F (6/05)Programming the CM6800EThe CM6800E is shipped from the factory with default programming settings. If the defaults are acceptable, th

C1528M-F (6/05) 413. At the ******* prompt, enter the DEFAULT PASSWORD: 2899100The Main Menu appears.Figure 32. CM6800E Programming Main MenuSelect L

42 C1528M-F (6/05)NAVIGATE AND SELECT OPTIONS/FIELD ENTRIES IN PROGRAMMING MODEDuring programming, a menu appears on the monitor screen. The currently

C1528M-F (6/05) 43Select option in a programming field. All Keyboards1. Scroll through the options until the appropriate entry appears in the field.2.

44 C1528M-F (6/05)ACCESSThe CM6800E supports the following ways to restrict switching system access:Keyboard to Monitor: Restrict a keyboard from acce

C1528M-F (6/05) 45ALARM PROGRAMMINGAlarmed cameras can be displayed on one or several monitors as part of one or several alarm groups (each monitor ca

46 C1528M-F (6/05)PROGRAM AN INTERNAL OR EXTERNAL ALARM CONTACTUse the Alarm Contact screens to configure alarm inputs. When an alarm is triggered, the

C1528M-F (6/05) 473. In the STP matrix, configure up to eight steps to be triggered as a result of this alarm.a. In the CAM field select a camera (use t

48 C1528M-F (6/05)PROGRAM A VIDEO LOSS ALARMUse the Video Loss screen to program the CM6800 to detect video loss from any camera input and indicate th

C1528M-F (6/05) 49ASSIGN A LOGICAL ALARM NUMBER (OPTIONAL)Each CM6800E alarm type (internal, external, and video loss) has been assigned a series of d

C1528M-F (6/05) 5 List of Illustrations 1 Sample CM6800E-48X8 System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

50 C1528M-F (6/05)AUXILIARY OUTPUTSThe three local auxiliary (AUX) outputs on the rear panel of the CM6800E can be operated manually from a system key

C1528M-F (6/05) 51CAMERA PROGRAMMINGExtended Coaxitron protocol receivers can be operated without any programming changes, other than changing the cam

52 C1528M-F (6/05)PROGRAM CAMERASFigure 40. Program Cameras1. In the CAMERA field, select the logical camera number of the video input to be defined.2.

C1528M-F (6/05) 534. Select the camera title. This title (up to 20 characters) appears on the monitor during real-time camera display.a. Navigate to t

54 C1528M-F (6/05)EVENT TIMERSYou can automate system operation to activate sequences or macros on specific monitors. Events can be scheduled on a dail

C1528M-F (6/05) 55MACROSMacros simplify operator control by grouping multiple functions into a single command.Figure 42. Macro ScreenMACRO: Select t

56 C1528M-F (6/05)MONITOR DISPLAYUse the Monitor screen to adjust monitor display settings for your system. You can adjust settings for the current mo

C1528M-F (6/05) 57MON/ALM NUMBER: Enable (ON) or disable (OFF) on-screen display of the monitor/alarm number. During normal operation, the monitor nu

58 C1528M-F (6/05)PASSWORDUse the Set Password screen to change the system password. If you change the password and then forget the new one, you will

C1528M-F (6/05) 59PORTS (SERIAL/COM PORTS) Use the Port screen to configure the settings for each device connected to a Serial/COM port on the rear pan

6 C1528M-F (6/05) 61 CM9760-MGR Link Cameras Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

60 C1528M-F (6/05)PRIORITYThe CM6800E provides eight levels of priority control. Each level defines the ability of a keyboard to control a pan/tilt/zoo

C1528M-F (6/05) 6196 X 16 SYSTEM SETTINGSWhen you connect two CM6800E-48X8 units together in a 96 x 16 system, you must access the System programming

62 C1528M-F (6/05)SEQUENCESThe CM6800E provides two types of sequences:• An operator can program a scratchpad sequence from an individual monitor, wit

C1528M-F (6/05) 63SEQUENCE: Select the sequence number you want to program.STP: Each sequence can include up to 72 steps. For each step select entries

64 C1528M-F (6/05)TIME AND DATEUse the Time and Date screen to set the system time and date settings. The time and date displayed on the monitor durin

C1528M-F (6/05) 65OperationsOVERVIEWA brief description of CM6800E operation is provided here. Refer to the following sections for detailed instructio

66 C1528M-F (6/05)SELECT CAMERASIf you select a restricted camera view, the camera view does not appear on that monitor. The previously selected, unre

C1528M-F (6/05) 67OPERATE SEQUENCESYou can run a scratchpad sequence from an individual monitor or a system sequence on any monitor accessible from th

68 C1528M-F (6/05)RUN A MACROA macro runs until the last step is completed (unless you specify a loop in the macro).KBD100/200A/300A KEYBOARDS KBD960/

C1528M-F (6/05) 69ACKNOWLEDGE AN ALARMWhen an alarm is triggered, an alarm icon appears on the monitors programmed to show that alarm.CALL A PRESETPro

C1528M-F (6/05) 7 Important Safeguards and Warnings 1. Read, keep, and follow these instructions.2. Heed all warnings.3. There are no user-serviceabl

70 C1528M-F (6/05)CREATE AND RUN A PATTERNPatterns are not available with the KBD100 keyboard.KBD200A/300A KEYBOARDS KBD960/KBR960 KEYBOARDSCreate a L

C1528M-F (6/05) 71OPERATE AUXILIARIES/RELAYSLocal auxiliaries are the outputs on the rear panel of the CM6800E. External auxiliaries are available by

72 C1528M-F (6/05)CONTROL GENEX MULTIPLEXER AND GENEX MULTIPLEXER DISPLAYSMultiplexer control is not available with the KBD100.OPERATE SCANNING FUNCTI

C1528M-F (6/05) 73AppendixCM6800E DIP SWITCHESFigure 52. CM6800E DIP Switches – Factory Default SettingsTable G. CM6800E DIP Switch SettingsCM6800E

74 C1528M-F (6/05)ALARM GROUP DISPLAY OPTIONSTo display on a monitor, an alarm must be assigned to an alarm group (A-H). Before programming alarms you

C1528M-F (6/05) 75REVERSE CHRONOLOGICAL PAIR: M AND LThe most recent alarm of a specific group is displayed on one designated monitor, while all other

76 C1528M-F (6/05)MACRO COMMANDSTable H provides a description of each macro command and the additional fields required for each command. Refer to the

C1528M-F (6/05) 77PIPO Turn off multiplexer picture-in-picture view. Multiplexer input CameraMonitor MonitorQUAD Display multiplexer four-camera mode.

78 C1528M-F (6/05)USING THE CM6800E-48X8 AS A SATELLITE DEVICE IN A 9700 SYSTEMThe CM6800E-48X8 can function as a remote satellite switcher in a 9700

C1528M-F (6/05) 79Figure 53. Data and Tie Line Connections Between CM6800E-48X8 and CM9700/CM9740/CM97604. After completing system installation and p

8 C1528M-F (6/05) Description Pelco’s CM6800E Matrix Switcher/Controller is a cross-point video matrix switcher. The CM6800E-48X8 provides switching

80 C1528M-F (6/05)CONFIGURE THE CM6800E AS A SATELITE DEVICEIn addition to any programming needed for the devices connected to the CM6800E-48X8 (such

C1528M-F (6/05) 81Satellite Port SettingsChange the device setting to SATELLITE for Port 7. The REPORT ALARMS setting changes to ON by default. If you

82 C1528M-F (6/05)Satellite Alarms (Optional)1. Enable the appropriate internal and external alarm contacts. Refer to the Alarm Contacts section for d

C1528M-F (6/05) 83CONFIGURE CM9700-MGR SYSTEM MANAGER SETTINGSInstructions for configuring the CM6800-E-48X8 as a satellite device with the CM9700-MGR

84 C1528M-F (6/05)CONFIGURE CM9760-MGR SYSTEM MANAGER SETTINGSInstructions for configuring the CM6800-E-48X8 as a satellite device with the CM9760-MGR

C1528M-F (6/05) 85Program the Comms File1. Click the Comms tab. The Comms page appears.Figure 59. CM9760-MGR Comms Page2. In the list of Defined Ports

86 C1528M-F (6/05)Program the Cameras File1. Click the Cameras tab. The Cameras page appears.Figure 60. CM9760-MGR Cameras PageComplete the following

C1528M-F (6/05) 87Program the Link Cameras File1. Click the Link Cameras tab. The Link Cameras page appears.Figure 61. CM9760-MGR Link Cameras PageCo

88 C1528M-F (6/05)Program the Alarms File (Optional)1. Click the Alarms tab. The Alarms page appears.Figure 62. CM9760-MGR Alarms PageComplete the fo

C1528M-F (6/05) 89NAVIGATE WITH THE CM9740/CM9760 KEYBOARDWhen using the CM6800E as a satellite device in a CM9740/CM9760 system, you can navigate the

C1528M-F (6/05) 9 Figure 2. Sample CM6800E 96 x 16 System Figure 3. Sample CM9760 System with CM6800E-48X8 as a Satellite SwitcherCM6800E-48X8 MA

90 C1528M-F (6/05)LOGICAL NUMBER ASSIGNMENT TABLE – FOR LINK CAMERASLink Camera Name Link Camera Number in the CM9740/CM9760 System(Link Camera page:

C1528M-F (6/05) 91ASCII OPERATING COMMANDSASCII protocol uses the ASCII character set to transmit and receive commands between an ASCII device (such a

92 C1528M-F (6/05)Pan leftPan rightStop pan leftStop pan right[1-64]La[1-64]Ra~La~RaMoves the currently selected pan and tilt device left or right at

C1528M-F (6/05) 93Acknowledge alarm [1-9999]Ia Acknowledges an existing alarm.Arm internal alarmArm external alarmArm video loss alarmDisarm internal

94 C1528M-F (6/05)TROUBLESHOOTINGGAINING INITIAL CONTROLIf you are having problems gaining control of your system for the first time:• Confirm that all

C1528M-F (6/05) 95SOFTWARE RESETPelco strongly recommends uploading system settings to the CM6800E-MGR before the software reset – this will allow you

96 C1528M-F (6/05)SOLUTIONS TO COMMON PROBLEMSRefer to Table K for a list of common problems and their solutions.Table K. Solutions To Common Problem

C1528M-F (6/05) 97KBD960/KBR960 ICON/BUTTON LEGENDFigure 67. Icon/Button LegendMUXCAMERA CONTROLSEQUENCEMENUMUXMENUSEQMUXFORWARDRUNBACKWARDMACRORECAL

98 C1528M-F (6/05)UPGRADE THE CM6800 SWITCHER SOFTWAREWhen you expand a CM6800E-48X8 system to a 96 x 16 system, verify that all system software is up

C1528M-F (6/05) 99GlossaryAccess The CM6800E allows you to restrict system control by (1) limiting the monitors or cameras a keyboard can access, or (